时间戳

首页 > 解决方案 > PIC - timer0 和中断计数和闪烁 LED

pic - PIC - timer0 和中断计数和闪烁 LED

问题描述

我正在使用带有中断的 PIC10F322 和 timer0，试图让 LED 闪烁，打开 1 秒，然后再关闭 1 秒。我曾尝试编写要求中断的计时器，并且效果很好。但是计算时间是不正确的。计数大约持续 2 秒，然后又关闭 2 秒，这是不正确的。我想知道计算有什么问题吗？芯片是16MHZ，定时器0是8位，预分频器设置为256。我的尝试是每1ms触发一次中断，然后进行999循环计数以达到1秒。

我的计算是：

256 - [(Delay * Fosc) / (prescaler*4)] = 256 - [(1ms * 16000000)/(256*4)] = 240


#define _XTAL_FREQ 16000000
#include <xc.h>

#pragma config FOSC = INTOSC    // Oscillator Selection bits (INTOSC oscillator: CLKIN function disabled)
#pragma config BOREN = OFF      // Brown-out Reset Enable (Brown-out Reset disabled)
#pragma config WDTE = OFF       // Watchdog Timer Enable (WDT disabled)
#pragma config PWRTE = OFF      // Power-up Timer Enable bit (PWRT disabled)
#pragma config MCLRE = OFF       // MCLR Pin Function Select bit (MCLR pin function is MCLR)
#pragma config CP = OFF         // Code Protection bit (Program memory code protection is disabled)
#pragma config LVP = OFF        // Low-Voltage Programming Enable (High-voltage on MCLR/VPP must be used for programming)
#pragma config LPBOR = ON      // Brown-out Reset Selection bits (BOR disabled)
#pragma config BORV = LO        // Brown-out Reset Voltage Selection (Brown-out Reset Voltage (Vbor), low trip point selected.)
#pragma config WRT = OFF        // Flash Memory Self-Write Protection (Write protection off)

int z = 0,count=0;
void main(void) {

    ANSELA = 0x00;

    TRISA = 0b0100;
    TRISAbits.TRISA2 = 1;
    LATAbits.LATA0 = 0;

    INTCONbits.GIE=1;       /* Enable Global Interrupt*/
    INTCONbits.PEIE = 1;  /* Enable peripheral Interrupt */

    OPTION_REGbits.T0CS = 0;

    OPTION_REGbits.PSA = 0; 
    OPTION_REGbits.PS0 = 1; /* set prescaler to 256 */
    OPTION_REGbits.PS1 = 1;
    OPTION_REGbits.PS2 = 1;
    OPTION_REGbits.INTEDG = 0;
    TMR0 = 240;
    INTCONbits.TMR0IF = 0;
    INTCONbits.TMR0IE = 1;

    while(1){
    }

   return; 
}


void __interrupt(high_priority) tcInt(void)
{

    if (TMR0IE && TMR0IF)
    {
        TMR0 = 240;
        TMR0IF = 0;

        if (count == 999)
        { 
            z = 0;
            LATAbits.LATA0 = ~LATAbits.LATA0;
            count =0;
        }
        count++;
    }

 return;
}

标签： pic

解决方案

你的定时器计算很好，但我猜你的微控制器运行在 8 MHz，如果你使用内部振荡器（#pragma config FOSC = INTOSC），这是复位后的默认值。如果您喜欢 16 MHz，则必须在OSCCON寄存器中进行选择。

OSCCON = 0b01110000;

推荐阅读